Regal Series Surface Mounted Vertical Flatwall
Regal Series Surface Mounted Vertical Flatwall

Vertical Headwalls

The Regal Series Surface Mounted Vertical Flatwall simplifies the organization of medical service equipment in an aesthetically appealing vertical headwall.

DOWNLOADS:
BROCHUREMANUALSSPEC SHEETSDRAWINGS

Regal Series Surface Mounted Vertical Flatwall Drawings

FilenameSizeType
arch_dr_vh_rsmf_fw38fl-sm-gen-p0.4MBDWG
arch_dr_vh_rsmf_fw38fl-sm-gen-p0.1MBPDF
arch_dr_vh_rsmf_fw1905-sm-gen-p0.41MBDWG
arch_dr_vh_rsmf_fw1905-sm-gen-p0.1MBPDF
arch_dr_vh_rsmf_fw2807-sm-gen-p0.4MBDWG
arch_dr_vh_rsmf_fw2807-sm-gen-p0.1MBPDF

General Features

  • Vertical headwall configuration ensures all services are at patient’s bedside
  • Increased equipment management with four integrated vertical accessory rails per headwall unit
  • Greater flexibility allowing services on all sides of the headwall unit
  • Vertical rails can be used for IT, monitor, cord and equipment management
  • Expandable to meet your future requirements

Recommended for all acuity levels including:

  • Emergency Department/Trauma
  • LDR
  • Transitional Step-Down
  • Patient Rooms
  • Special Procedure

Equipment Management

Custom Outlet Placement

Optional Valance

Easy to Clean

Removable Fascia

  • Easily add, change and maintain services in your headwall

Streamlined Installation

  • Installed on top of the wall with services terminated above the ceiling line

Hard Piped Gases and EMT Conduit

Materials and Construction

  • 14", 19", 28" and 38" (35.56 cm, 48.26 cm, 71.12 cm and 96.52) standard sized headwall units reduce clutter and allow for access to services
  • Four integrated accessory rails are clear etched anodized.
  • Fascia is anodized aluminum finish where devices are located. All other fascia to be MDF with high pressure laminate (HPL).
  • Amico medical gas outlets, DISS or quick connection type, console style.
  • Medical gas distribution shall be supplied by pipe drops to a single point connection above the unit. All Medical Gas Outlets and piping shall be brazed and tested in accordance with NFPA 99c.
  • Wire for standard and critical branch power circuits shall be #10 or #12 type THHN stranded copper wire, 600 volt, with heat resistant thermoplastic insulation.
  • All ground conductors shall be installed in conduit. Where electrical terminations are located inside the flatwall, a grounding bus will be installed for each type of power, and shall be installed as to ensure grounding for the complete power system.
  • Electrical receptacles shall be Hubbell Hospital Grade 15 or 20 amp, 120 or 277 volt, UL listed and marked Hospital Grade. Simplex, duplex, and (optional) safety receptacles shall be NEMA style 5-15R or 5-20R. Optional locking receptacles shall be simplex type, 20 amp, 120 or 277 volt, color black, and be HUBBELL lock 23000 HG style.
  • Low voltage data provisions shall be connected to device junction box via conduit. Amico Corporation shall include pull cord extending from service provision to electrical termination point.
  • Switching shall be HUBBELL Industrial Grade 120 or 277 volt, 15 or 20 amps. Switch type options include SPST, 3-Way or Momentary. Low Voltage Switching will be 0-12 volts, 15 amps unless otherwise noted. Amico Corporation shall furnish, preinstall and wire all switches.
  • Optional lighting can be provided by the Amico Skyline Overbed Light.
  • An optional decorative wood valance can be added on and between two flatwall units to complement the room. The wood valance is constructed of particle board with laminate finish, colored to match the flatwall. The integrated light is a 3' (91.44 cm) fluorescent light with two bulbs provide by Amico and provides reading light above the bed.

Additional Specifications

Fascia Colors

Choose from over 2000 colors that are available from major laminate manufacturers
  

Languages

  • English
  • Français
  • Español